Heavy Duty Smb W01 - M58 - 0736 Truck Air Springs 1dk21b5 Fruehauf For Phoenix

Heavy Duty Smb W01 - M58 - 0736 Truck Air Springs 1dk21b5 Fruehauf For Phoenix

Production Description

Truck Air Suspension Bag

OEM No: W01-M58-0736

Contitech: 4159NP05

Firestone: W01-M58-0736 1T15M-9

Appliion: Phoenix

Air Spring

Air springs are the only load support product that provide BOTH leveling capacity and improved ride comfort. Only air springs give you load support that is adjustable for your specific load. Add air when riding loaded to ensure your vehicle is level for a safer, more comfortable ride. Deflate the air springs when riding unloaded for optimal ride quality.

The Benefits of Air Spring

1. Eliminate Squat

Is the rear end of your vehicle sitting low from a heavy load? This is called squat or sag. Lift it back up where it belongs and enjoy the benefits listed below. This is especially beneficial while towing: adjust the air springs to accept the tongue weight of the trailer.

2. Reduce Poor Braking and Steering

The two front tires bear the majority of braking and steering. Air spring ensures that weight is properly distributed to all four tires for optimal braking and steering.

3. Eliminate Rough Ride

Progressive rate air springs significantly improve ride quality by better absorbing road inputs, while keeping your tires on the road for better handling.

4. Eliminate Poor Headlight Aim

Your headlights should be on the road and not in the trees. Only level and stable vehicles provide safe and proper headlight aiming—critical for safe night driving.

Production Picture

Our Advantages

• Long lasting service on almost all truck and trailer air suspensions
• Absorb road shock to help tractors and rigs last longer
• Cut down on vibration and driver fatigue
• Long, trouble free service, constant level hauling, quite cushioned ride

Warning and Tips

Maintenance of the air springs, Vehicle Check-List

• Check the air lines and devices of leakage and that they turns freely.
• Check the bellows bearing for damage, correct fastening, deformation, sharp edges.
• Check the shock absorbers for operation and impermeability as well as tightness and bearing.
• Periodically, check nuts and bolts for proper torque. For specific recommendations see manufacturer's manual.
• Check axle suspension, trailing arms and rods for wear.
• Check height control valve to see that it is functioning properly. A properly maintained valve will save unneeded maintenance expense.
• Routine inspection of all of the above according to manufacturer's instructions, will extend the life of your vehicle and reduce your overall maintenance expense.

Air Spring Installation

1. Before you start installing air springs, make sure you have all the necessary tools and equipment to perform the repair safely.
2. Familiarize yourself with the suspension on which you are performing the repair by reviewing the manufacturers service guide.
3. If you are in doubt about something, ask for assistance from a qualified suspension specialist, the suspension manufacturer or the air spring manufacturer; This can save you a lot of time and aggravation later in the job.

Important tips to remember when installing a new unit

• Check levelling valve, linkage and transmission parts for wear and damage and if necessary replace the damaged parts.

• Check that the shock absorber for leakages and take a shock absorber test. A defective shock absorber must be replaced.

• Once the air lines are disconnected, check their entire length for cracks or other damage. Replace worn parts.

• With the air spring removed, other parts of the air suspension become more accessible. Check for wear or damage of the frame hangers, trailing arm bushings, torque rods, the trailing arms and the air spring mounts. When it is necessary, also replace parts.

• Check bearing for air spring bellow for external damage, deformation, sharp edges and correct fastening.

• Before installing the new unit, clean the air spring mounting plates to ensure proper attachment to the suspension.

• Always use new attaching bolts for the installation and observe the tightening torques. Never use old bolts, because these can fall out.

• Check the linkage of the levelling valve to see that it is functioning properly. Under load, the linkage should move from the neutral position up to the intake position. This lets air into the springs, which brings the arm back to the neutral position. This lets air into the springs, which brings the arm back to the neutral position. That opens the exhaust valve, allowing air to escape until the arm returns to the neutral position. Then check the driving level.

Company Information:

Guangzhou Tech Master Auto Parts Co. Ltd. is a professional company specializing in developing, producing and exporting air suspension parts, such as, air spring, air strut, air shock absorber, air compressor, power steering pump, steering rack, control arms, other spare parts and suspension accessories, especially for Mercedes-Benz, BMW, Audi, Land Rover, Lincoln, and Ford. We also supply other models of the air suspension parts and a series of high-grade heavy truck front and rear air springs.

Contact Us:

If you have any questions, please feel free to contact with us. We would be very glad to help you. We will get back to you within 24 hours or get back to you immediately.

Contact Name: Jennifer Qiu

Skype:air-springs

Tel: 0086 18819146976 (WhatsApp)

Guangzhou Tech Master is a manufacturer of air suspension parts with 16 years of production experience. Mainly produces air suspension shock absorbers, repair kits, air compressors and valve blocks for luxury vehicles such as Mercedes Benz, BMW, Audi, Land Rover, etc. Mainly sold to Europe, Russia, Middle East, Southeast Asia, South America and South Africa.