
Wafer Lugged Resilient Sealing Butterfly Valve , Manual Operation Ductile Iron
Brief introduction:
The butterfly valve is operated by the disc rotating form 0° to 90°, can be applied to cut off or regulate
the flow of medium.
The valve can be actuator by operating lever, handle wheel electric actuator or pneumatic actuator.
Widely used for potable water supply and distribution, waste water treatment, electric power plant, gas
supply, warm-air system, smelting plant, ship building, textile, petroleum, chemistry, or other light
industries.
Features:
⊙ Low weight
⊙ Compact structure
⊙ Low flow resistance
⊙ Small operation torque
⊙ Easy to install and maintain
⊙ Flow pattern tend to be straight
⊙ Open-close 90° more smoothly
Mail part & material
Main Hand Lever :Aluminum Alloy,
Plastic Auxiliary Hand lever : Aluminum Alloy,
Plastic Spring: Common Spring Stainless Steel Spring
Technical Specification
- Nominal diameter: 50~200(2″~ 8″)
- Nominal pressure: 1.0/1.6/2.0Mpa
- Applicable Temperature: -10℃~150℃
- Drive mode:Aluminum alloy hand lever.
- Applicable medium: freshwater,sea water,food,natural
gas,alcoholic,salt,acid,alkali,oil,steam,air etc.
Butterfly Valve Specification | A (mm) | A 1 (mm) | H(mm) | Total Weight (Kg) | ||
A-type | LT-type | A-type | LT-type | |||
DN25-32 | 150 | - | 115 | 180 | 2.0 | - |
DN40 | 160 | - | 115 | 190 | 2.2 | - |
DN50 | 216 | 248 | 170 | 260 | 2.4 | 3.17 |
DN 65 | 223 | 258 | 280 | 2.67 | 4.00 | |
DN 80 | 231 | 265 | 304 | 2.87 | 4.97/5.67 | |
DN100 | 335 | 367 | 200 | 340 | 5.00 | 7.50 |
DN125 | 349 | 386 | 260 | 375 | 7.3 | 11.5 |
DN150 | 362 | 401 | 407 | 8.8 | 12.5 |
Features:
⊙ Professional design
When initiating the rotary opening movement the disc is off-seated after only a few
degree of opening movement and there is very little wear and tear between seat ring and disc.
⊙ Combine fastness
Stainless steel seat ring is rolled into the valve body by applying special rolling technology
when DN<1200. Ultrasonic spray applies seal of valve body when DN>1400.
⊙ Adjust tightness
Rubber sealing ring and disc can adjust tightness or softness of sealing with clamping ring, it insures
best performance of adjusting the compression of sealing.
⊙ Sealing reliable
Body and disc made of ductile iron which promote the impact resistance and pressure-bearing
capacity, sealing ring made of rubber and valve seat’s sealing surface is conical shaped, make the
sealing capacity more reliable.
⊙ Excellent corrosion protection
Inside electrostatic epoxy resin power coating or vitreous enamel(upon request), outside electrostatic
epoxy resin power coating.
⊙ Reliable health nature
Epoxy resin power is up to the health standard.
Mail part & material
Body, Disc: GGG50 with internal and external epoxy resin coating
Stems: 1Cr17Ni12Mo2Ti, Stainless steel min.13%Cr
Bushing :Bronze CuAI10Fe3
Seal ring, O-ring: NBR, EPDM or FPM
Technical Specification
-Nominal diameter: 150~2600mm
-Nominal pressure: 1.0/1.6/2.5Mpa
-Strength testing pressure: 1.5/2.4/3.75Mpa
-Sealing testing pressure: 1.1/1.76/2.75Mpa
Executive standard
Design standard | DIN3354 |
Face to face | DIN3202 or BS 5155 |
Flange end | DIN 2501 |
Test & inspection | DIN 3230 or GB/T 13927 |
Working temperature | NBR<80℃; EPDM<120℃; FPM<160℃ |
Main external and connection dimension
1.0MPa mm
DN | L | H1 | H2 | H3 | Flange dimensions comply with DIN 2501 | ||||||
long type | short type | O | C | g | f | b | n-d | ||||
150 | 210 | 140 | 226 | 165 |
| 285 | 240 | 212 | 3 | 19 | 8-23 |
200 | 230 | 152 | 255 | 192 |
| 340 | 295 | 268 | 3 | 20 | 8-23 |
250 | 250 | 165 | 293 | 227 |
| 395 | 350 | 320 | 3 | 22 | 12-23 |
300 | 270 | 178 | 326 | 260 |
| 445 | 400 | 370 | 4 | 24.5 | 12-23 |
350 | 290 | 190 | 368 | 314 |
| 505 | 460 | 430 | 4 | 24.5 | 16-23 |
400 | 310 | 216 | 423 | 346 | 634 | 565 | 515 | 482 | 4 | 24.5 | 16-28 |
450 | 330 | 222 | 455 | 385 | 666 | 615 | 565 | 532 | 4 | 25.5 | 20-28 |
500 | 350 | 229 | 506 | 422 | 728 | 670 | 620 | 585 | 4 | 26.5 | 20-28 |
600 | 390 | 267 | 568 | 490 | 790 | 780 | 725 | 685 | 5 | 30 | 20-31 |
700 | 430 | 292 | 632 | 550 | 854 | 895 | 840 | 800 | 5 | 32.5 | 24-31 |
800 | 470 | 318 | 692 | 615 | 924 | 1015 | 950 | 905 | 5 | 35 | 24-34 |
900 | 510 | 330 | 815 | 678 | 1098 | 1115 | 1050 | 1005 | 5 | 37.5 | 28-34 |
1000 | 550 | 410 | 880 | 743 | 1163 | 1230 | 1160 | 1110 | 5 | 40 | 28-37 |
1200 | 630 | 470 | 1024 | 860 | 1307 | 1455 | 1380 | 1330 | 5 | 45 | 32-40 |
1400 | 710 | 530 | 1210 | 1010 | 1350 | 1675 | 1590 | 1535 | 5 | 46 | 36-43 |
1600 | 790 | 600 | 1340 | 1140 | 1480 | 1915 | 1820 | 1760 | 5 | 49 | 40-49 |
1800 | 870 | 670 | 1460 | 1360 | 1640 | 2115 | 2020 | 1960 | 5 | 52 | 44-49 |
2000 | 950 | 760 | 1660 | 1485 | 1800 | 2325 | 2230 | 2170 | 5 | 55 | 48-49 |
1.6MPa mm
DN | L | H1 | H2 | H3 | Flange dimensions comply with DIN 2501 | ||||||
long type | short type | O | C | g | f | b | n-d | ||||
150 | 210 | 140 | 226 | 165 |
| 285 | 240 | 212 | 3 | 19 | 8-23 |
200 | 230 | 152 | 255 | 192 |
| 340 | 295 | 268 | 3 | 20 | 12-23 |
250 | 250 | 165 | 293 | 227 |
| 405 | 355 | 320 | 3 | 22 | 12-28 |
300 | 270 | 178 | 326 | 260 |
| 460 | 410 | 378 | 4 | 24.5 | 12-28 |
350 | 290 | 190 | 368 | 314 |
| 520 | 470 | 438 | 4 | 26.5 | 16-28 |
400 | 310 | 216 | 423 | 346 | 634 | 580 | 525 | 490 | 4 | 28 | 16-31 |
450 | 330 | 222 | 455 | 385 | 666 | 640 | 585 | 550 | 4 | 30 | 20-31 |
500 | 350 | 229 | 506 | 422 | 728 | 715 | 650 | 610 | 4 | 31.5 | 20-34 |
600 | 390 | 267 | 568 | 490 | 790 | 840 | 770 | 725 | 5 | 36 | 20-37 |
700 | 430 | 292 | 632 | 550 | 854 | 910 | 840 | 795 | 5 | 39.5 | 24-37 |
800 | 470 | 318 | 692 | 615 | 924 | 1025 | 950 | 900 | 5 | 43 | 24-40 |
900 | 510 | 330 | 815 | 678 | 1098 | 1125 | 1050 | 1000 | 5 | 46.5 | 28-40 |
1000 | 550 | 410 | 880 | 743 | 1163 | 1255 | 1170 | 1115 | 5 | 50 | 28-43 |
1200 | 630 | 470 | 1024 | 860 | 1307 | 1485 | 1390 | 1330 | 5 | 57 | 32-49 |
1400 | 710 | 530 | 1210 | 1010 | 1350 | 1685 | 1590 | 1530 | 5 | 60 | 36-49 |
1600 | 790 | 600 | 1340 | 1140 | 1480 | 1930 | 1820 | 1750 | 5 | 65 | 40-56 |
2.5MPa mm
DN | L | H1 | H2 | H3 | Flange dimensions comply with DIN 2501 | ||||||
long type | short type | O | C | g | f | b | n-d | ||||
150 | 210 | 140 | 226 | 165 |
| 300 | 250 | 211 | 3 | 20 | 8-28 |
200 | 230 | 152 | 255 | 192 |
| 360 | 310 | 274 | 3 | 22 | 12-28 |
250 | 250 | 165 | 293 | 227 |
| 425 | 370 | 330 | 3 | 24.5 | 12-31 |
300 | 270 | 178 | 326 | 260 |
| 485 | 430 | 390 | 4 | 27.5 | 16-31 |
350 | 290 | 190 | 368 | 314 |
| 555 | 490 | 450 | 4 | 30 | 16-34 |
400 | 310 | 216 | 423 | 346 | 634 | 620 | 550 | 500 | 4 | 32 | 16-37 |
450 | 330 | 222 | 455 | 385 | 666 | 670 | 600 | 560 | 4 | 34.5 | 20-37 |
500 | 350 | 229 | 506 | 422 | 728 | 730 | 660 | 610 | 4 | 36.5 | 20-37 |
600 | 390 | 267 | 568 | 490 | 790 | 845 | 770 | 720 | 5 | 42 | 20-40 |
700 | 430 | 292 | 632 | 550 | 854 | 960 | 875 | 820 | 5 | 46.5 | 24-43 |
800 | 470 | 318 | 692 | 615 | 924 | 1085 | 990 | 930 | 5 | 51 | 24-49 |
900 | 510 | 330 | 815 | 678 | 1098 | 1185 | 1090 | 1028 | 5 | 55.5 | 28-49 |
1000 | 550 | 410 | 880 | 743 | 1163 |
|
|
| 5 |
|
|
1200 | 630 | 470 | 1024 | 860 | 1307 |
|
|
| 5 |
|
|
1400 | 710 | 530 | 1210 | 1010 | 1350 |
|
|
| 5 |
|
|
1600 | 790 | 600 | 1340 | 1140 | 1480 |
|
|
| 5 |
|
|
1. BRIEF INTRODUCTION:
The butterfly valve is operated by the disc rotating form 0° to 90°, can be applied to cut off or regulate
the flow of medium.
The valve can be actuated by operating lever, handle wheel electric actuator or pneumatic actuator.
Widely used for potable water supply, waste water treatment, electric power plant, gas supply,
warm-air system, smelting plant, ship building, textile, petroleum, chemistry, or other light industries.
2. Specification
name | Butterfly Valve | |
Item No | D373H-10K | |
DN(mm) | DN50~DN3000 | |
pressure(Mpa) | 1.0 | |
Test pressure (Mpa) | Seal test | 1.1 |
Body test | 1.5 | |
temperature | ≤350℃ | |
medium | Water, sewage, sea water, hot water etc., |
3. FEATURES
⊙ EPDM seated, good seal
⊙ Low weight
⊙ Low flow resistance
⊙ Small operation torque
⊙ Easy to install and maintain
⊙ Open-close 90° more smoothly
4. APPLICABLE STANDARDS
1. Design according : API 609
2. Test standard according: JIS B2003
3. Connect flange standard according: JIS B2212
4. Face to face standard according: JIS B2002
5. Item Name of part Material Spec
NO | Part name | Material |
1 | Body | SS304 |
2 | Gear box | Assembly |
3 | Disc | SS304 |
4 | Stem | SS416 |
5 | Seal ring | 316+Graphite |
6 | packing | Graphite |
6. Operation:
6.1. The two pipe flange should be smooth.
6.2. Put the butterfly valve in the pipe line, fixed the orientation hole first.
7. Delivery:
When delivery or store the butterfly valve, should keep in dry and cool environment.
8. Note:
8.1. Pipe flange should same as the butterfly valve flange.
8.2. Check the valve before installed, the environment should correspond to the butterfly valve
specification.
8.3. Before open butterfly valve, checking the disc without dirt.
8.4. The disc must be shut off place when installed.
8.5. Adjusting the pipe connect before installed.
8.6. The connect flange should be parallel.
8.7. After installed, the pressure test disc should be open place.
8.8. If the butterfly can not natural open or close, please kindly check it careful, can not strike, tamp or
use extension lever.
8.9. When maintenance or operation, must check the stem, lever, gear box or actuator have correctly
connect. Otherwise the stem will be push by pipe pressure.
9. The malfunction and resolving:
malfunction | whys | solution |
Seal leak | 1, Some rubbish on the seal 2, Seal have been light damage | ① Clean the rubbish. ② Replacing the disc |
Stem Packing leak | 1, packing be damaged 2, packing lapse | ① Tighten the gland nut ② Change the packing |
flange leak | 1, the nut release 2, gasket lapse | 1 . Tighten the nut 2. Change the gasket |
10. Maintenance
Open the worm box cover and add some butter per two months.
Check the seal, packing and flange, if leak, please maintain ASAP.
Specifications:
Size: DN50 - 3000
Temperature: -15℃ - 150℃
Pressure: 1.0MPa/1.6MPa
Materials
Materials of Body : Ductile Iron (GGG40, GGG50). Cast Iron (GG25),
Stainless Steel
Materials of Disc : Stainless Steel. Nickel Plated, Ductile Iron,
Ductile Iron Coated Plastic,
Titanium Steel, Copper Alloy etc
Materials of Seat : Ethylene-Propylene-Diene Monomer (EPDM),
Polytetrafluoroethylene (PTFE),
Nitrile Rubber (NBR), Chloroprene, Chlorosulfonated Polyethylene (Hypalon),
Silicon, Fluoroelastomer (VITON) , Caoutchouc etc.
Materials of Stem : Stainless Steel. Carbon Steel ,2Cr13
A butterfly valve is a type of flow control device, typically used
to regulate a fluid flowing through a section of pipe.
The valve is similar in operation to a ball valve. A flat circular
plate is positioned in the center of the pipe.
The plate has a rod through it connected to an actuator on the
outside of the valve. Rotating the actuator turns the
plate either parallel or perpendicular to the flow. Unlike a ball
valve, the plate is always present within the flow,
therefore a pressure drop is always induced in the flow regardless
of valve position.
Wafer Rubber Seated Butterfly Valves
DN | PN | Connection dimensions(mm) | |||
L | D | D1 | Zφd | ||
40 | 1.0/1.6 | 43 | 145 | 110 | 4-18 |
50 | 43 | 165 | 125 | 4-18 | |
65 | 46 | 185 | 145 | 4-18 | |
80 | 46 | 200 | 160 | 4-18/8-18 | |
100 | 52 | 220 | 180 | 8-18 | |
125 | 56 | 250 | 210 | 8-18 | |
150 | 56 | 285 | 240 | 8-22 | |
200 | 60 | 340 | 295 | 8-22/12-22 | |
250 | 68 | 395/405 | 350/355 | 12-22 | |
300 | 78 | 445/460 | 400/410 | 12-22 | |
350 | 1.0 | 78 | 505 | 460 | 16-22 |
400 | 102 | 565 | 515 | 16-26 | |
450 | 114 | 615 | 565 | 20-26 | |
500 | 127 | 670 | 620 | 20-26 | |
600 | 154 | 780 | 725 | 20-30 | |
700 | 165 | 895 | 840 | 24-30 | |
800 | 190 | 1015 | 950 | 24-33 | |
900 | 203 | 1115 | 1050 | 28-33 | |
1000 | 216 | 1230 | 1160 | 28-39 | |
1200 | 254 | 1455 | 1380 | 32-39 | |
1200 | 0.6/0.25 | 254 | 1400/1375 | 1340/1320 | 32-34/32-30 |
1400 | 279 | 1620/1575 | 1560/1620 | 36-34/36-30 | |
1600 | 318 | 1820/1785 | 1760/1730 | 40-34/40-30 | |
1800 | 356 | 2045/1985 | 1970/1930 | 44-41/44-30 | |
2000 | 406 | 2265/2185 | 2180/2130 | 48-48/48-30 |
Shanghai kangquan Valve Co. Ltd.
Shanghai KangQuan Valve Co. Ltd. is a specialized valves manufacture, which has 2,500 tons of
valves output capacity annually. We pay much attention to the quality so our products are superior in
quality compared with those of other manufacturers. After years of research and development, we have
accumulated a wealth of information and experience in this field. We enjoy a high reputation in dealing
with both domestic and overseas trading.
Shanghai KangQuan Valve Co. Ltd. covers an area of 15000 square meters. Our products line includes
various kinds of gate valves, globe valves, ball valves, check valves, cock valves, butterfly valves of , etc.,
up to the international advanced standards of ANSI, API, JIS, DIN, BS and so on . Materials mainly include
carbon steel ,stainless steel ,ductile iron and so on .with hand wheel worm-gear actuator and pneumatic
and electric actuator to be selected ,widely used in the industries of petrochemical, natural gas, metallurgy,
electric power , pharmaceutical , construction, etc..
With highly qualified professionals and first class service, Shanghai KangQuan Valve Co. Ltd. has
established a highly respected enterprise which has been relied on for years. And we will continuously
offer customers the most accurate and high quality delivery service possible.
Excellent quality assurance is our sales purpose,
Competitive price is our sales policy,
On time product delivery and responsive service is our standard.
Shanghai KangQuan Valve Co. Ltd. hopes to work together with you for a better future. Let’s work
together building a mutually beneficial relationship that will last for years.